Chip 1997 December

home *** CD-ROM | disk | FTP | other *** search

/ Chip 1997 December / CHIP Turkiye Aralık 1997.iso / grafik / masterc / demo / disk1 / mill6.prm < prev next >

Wrap

INI File | 1996-10-11 | 41.3 KB | 918 lines

[contour] 1 01250FLT // Tool reference 2 2 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.125 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 60 0 // Linear array: X axis: Steps 61 0.0 // Linear array: X axis: Distance 62 0 // Linear array: Y axis: Steps 63 0.0 // Linear array: Y axis: Distance 64 0 // Depth cuts: Rough: Steps 65 0.0 // Depth cuts: Rough: Distance 66 0 // Depth cuts: Finish: Steps 67 0.0 // Depth cuts: Finish: Distance 70 0.01 // Roll around sharp corners 71 // Rotary axis 72 0.0 // Rotary axis diameter 101 1 // Infinite look-ahead (0 = no, 1 = yes) 102 0 // Entry line is perpendicular (0 = no, 1 = yes) 103 0.0 // Entry line length 104 0.0 // Entry arc radius 105 1.5707963268 // Entry arc angle in radians 106 0 // Number of roughing cuts 107 0.0 // Rough cut spacing 108 1 // Number of finish cuts 109 0.0 // Finish cut spacing 110 0.001 // Linearization tolerance 111 0 // Contour depth is incremental (0 = no, 1 = yes) 112 0.0 // Incremental contour depth 113 0.005 // Maximum depth variance 114 1 // Finish all (0 = no, 1 = yes) [drill] 1 01250FLT // Tool reference 2 2 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.125 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 60 0 // Linear array: X axis: Steps 61 0.0 // Linear array: X axis: Distance 62 0 // Linear array: Y axis: Steps 63 0.0 // Linear array: Y axis: Distance 64 0 // Depth cuts: Rough: Steps 65 0.0 // Depth cuts: Rough: Distance 66 0 // Depth cuts: Finish: Steps 67 0.0 // Depth cuts: Finish: Distance 70 0.01 // Roll around sharp corners 71 // Rotary axis 72 0.0 // Rotary axis diameter 100 0 // Drill cycle 102 0 // Initial height is incremental (0 = no, 1 = yes) 103 0.2 // Incremental initial height 104 0 // Reference height is incremental (0 = no, 1 = yes) 105 0.1 // Incremental reference height 106 0 // Drill depth is incremental (0 = no, 1 = yes) 107 0.0 // Incremental depth 108 0.11 // First peck increment 109 0.1 // Subsequent peck increment 110 0.009 // Peck clearance 111 0.001 // Retraction distance 112 0.0 // Dwell 113 1.0 // Absolute initial height 114 0.1 // Absolute reference height 115 0 // Adjust depth per drill tip (0 = no, 1 = yes) 115 2.0594885173 // Drill tip angle in radians [pocket] 1 01250FLT // Tool reference 2 2 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.125 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 60 0 // Linear array: X axis: Steps 61 0.0 // Linear array: X axis: Distance 62 0 // Linear array: Y axis: Steps 63 0.0 // Linear array: Y axis: Distance 64 0 // Depth cuts: Rough: Steps 65 0.0 // Depth cuts: Rough: Distance 66 0 // Depth cuts: Finish: Steps 67 0.0 // Depth cuts: Finish: Distance 70 0.01 // Roll around sharp corners 71 // Rotary axis 72 0.0 // Rotary axis diameter 300 0 // Cutting method (0 = zig zag, 1 = spiral inside out, 2 = spiral outside in) 301 0.0 // Roughing angle 302 0.1 // Roughing step size 304 0 // Number of finish passes 305 0.0 // Finish pass step size 307 1 // Entry line is perpendicular (0 = no, 1 = yes) 310 0.0 // Entry line length 311 0.0 // Entry arc radius 312 1.5707963268 // Entry arc angle in radians 313 1 // Machine by region (0 = no, 1 = yes) 314 0 // Finish allowance 315 0 // Use additional finish parameters (0 = no, 1 = yes) 316 0 // Break arcs (0 = full circles, 1 = arcs, 2 = lines) 317 0.001 // Chordal deviation for breaking arcs into lines 320 1.5707963268 // Maximum angle for breaking arcs into arcs 321 0 // Optimize finish passes 330 0 // Tapered wall pocketing (1=yes, 0=no) 331 0.0523598775 // Tapered wall pocketing: Base taper angle in radians 332 0.0523598775 // Tapered wall pocketing: Island taper angle in radians 333 0.0 // Tapered wall pocketing: Initial Z 334 -1.0 // Tapered wall pocketing: Final Z 335 -0.25 // Tapered wall pocketing: Z step 350 0 // Finish: Cutter compensation in control (0 = no, 1 = yes) 351 0.0 // Finish: Roll around sharp corners 353 NONE // Finish: Material 354 01250FLT // Finish: Tool reference 355 2 // Finish: Tool number 356 1 // Finish: Tool diameter offset number 357 1 // Finish: Tool length offset number 360 0.125 // Finish: Tool diameter 361 0.0 // Finish: Amount of stock to leave 362 40.0 // Finish: Feed rate 363 20.0 // Finish: Plunge rate 364 5000 // Finish: Spindle speed 365 0 // Finish: Coolant 366 1.0 // Finish: Rapid depth 367 0.0 // Finish: Home position x 370 0.0 // Finish: Home position y 371 0.0 // Finish: Home position z 372 1 // Finish: Fillet for cutter compensation in control 380 0 // Helix: 0 = off, 1 = on 381 0.5 // Helix: maximum radius 382 0.0523598775 // Helix: ramp angle in radians 383 0.02 // Helix: maximum error 384 0 // Helix: 0 = CW, 1 = CCW 385 0.02 // Helix: xy clearance 386 0.5 // Helix: depth 387 0 // Helix: 0 = plunge to start, 1 = rapid to start 388 0.0 // Ramp direction [flowline] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 1 // Use chordal deviation (0 = no, 1 = yes) 101 0 // Cutting method 102 0 // Cutting direction 103 0.05 // Along distance 104 0.05 // Across distance 105 0.001 // Chordal deviation 106 0.001 // Scallop height 107 0 // Zig-Zag vectors: 1=yes, 0=no 108 0.0 // Zig-Zag vectors: Angle in radians 109 1.0 // Zig-Zag vectors: Length [finishparl] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 200 0.0 // Cut angle 204 0.001 // Chordal deviation 205 0.05 // Stepover distance 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used [roughparl] 1 03750FLT // Tool reference 2 14 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.375 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 200 0.0 // Cut angle 204 0.01 // Chordal deviation 205 0.25 // Stepover distance 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 233 1 // Allow negative z motion along surface: 0=no, 1=yes 234 1 // Allow positive z motion along surface: 0=no, 1=yes 235 0 // Plunge control: 0=multiplunge, 1=cut from one side, 2=cut from both sides 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 403 1 // Z depth control: 0: absolute, 1:incremental 404 0.01 // Incremental top clearance 405 0.01 // Incremental bottom stock 407 0.0 // Absolute top depth 408 -1 // Absolute bottom depth 410 0.1 // Z stepdown [finishrad] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 204 0.001 // Chordal deviation 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 613 0.0 // Start angle (degrees) 615 1 // Start position: 0=inside, 1=outside 616 0.01 // Start offset distance 618 360.0 // Sweep angle (degrees) 619 1.0 // Angular stepover (degrees) [roughrad] 1 03750FLT // Tool reference 2 14 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.375 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 204 0.01 // Chordal deviation 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 403 1 // Z depth control: 0: absolute, 1:incremental 404 0.01 // Incremental top clearance 405 0.01 // Incremental bottom stock 407 0.0 // Absolute top depth 408 -1 // Absolute bottom depth 410 0.1 // Z stepdown 613 0.0 // Start angle (degrees) 615 1 // Start position: 0=inside, 1=outside 616 0.01 // Start offset distance 618 360.0 // Sweep angle (degrees) 619 1.0 // Angular stepover (degrees) [finishproj] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 200 0.0 // Cut angle 204 0.001 // Chordal deviation 205 0.05 // Stepover distance 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 512 MPROJ.NCI // NCI filename to be projected [roughproj] 1 03750FLT // Tool reference 2 14 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.375 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 200 0.0 // Cut angle 204 0.01 // Chordal deviation 205 0.25 // Stepover distance 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 403 1 // Z depth control: 0: absolute, 1:incremental 404 0.01 // Incremental top clearance 405 0.01 // Incremental bottom stock 407 0.0 // Absolute top depth 408 -1 // Absolute bottom depth 410 0.1 // Z stepdown 512 MPROJ.NCI // NCI filename to be projected [finishctour] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 200 0.0 // Cut angle 204 0.001 // Chordal deviation 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 401 0.0 // Entry radius 402 0.0 // Exit radius 403 1 // Z depth control: 0: absolute, 1:incremental 404 0.01 // Incremental top clearance 405 0.01 // Incremental bottom stock 407 0.0 // Absolute top depth 408 -1 // Absolute bottom depth 410 0.1 // Z stepdown 414 1 // Order of z cuts: 0-bottom-to-top, 1-top-to-bottom 415 1 // Cut direction: 0-conventional, 1-climb 421 0 // Graphics cleanup: 0-none, 1-redraw, 2-erase screen 423 0.001 // Minimum contour length 431 1 // Open contour cut direction: 0-zigzag, 1-one way [roughctour] 1 03750FLT // Tool reference 2 14 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.375 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 200 0.0 // Cut angle 204 0.01 // Chordal deviation 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 401 0.0 // Entry radius 402 0.0 // Exit radius 403 1 // Z depth control: 0: absolute, 1:incremental 404 0.01 // Incremental top clearance 405 0.01 // Incremental bottom stock 407 0.0 // Absolute top depth 408 -1 // Absolute bottom depth 410 0.1 // Z stepdown 414 1 // Order of z cuts: 0-bottom-to-top, 1-top-to-bottom 415 1 // Cut direction: 0-conventional, 1-climb 421 0 // Graphics cleanup: 0-none, 1-redraw, 2-erase screen 423 0.001 // Minimum contour length 431 1 // Open contour cut direction: 0-zigzag, 1-one way [roughpock] 1 03750FLT // Tool reference 2 14 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.375 // Tool diameter 6 0.0 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 204 0.01 // Chordal deviation 208 0 // Cutting method: 0=zigzag, 1=one way 210 1 // Display offset intersections: 0=no, 1=yes 221 0 // Short gap motion (along a cut): 0=direct, 1=broken 223 0 // Prompt for start point: 0=no, 1=yes 226 0 // Use check surfaces: 0=no, 1=yes 227 0.0 // Stock to leave on check surfaces 228 0 // Prompt for tool center boundary: 0=no, 1=yes 229 2 // Long gap motion (along a cut): 0=direct, 1=broken, 2=retract 230 2 // Long gap motion (between cuts): 0=direct, 1=broken, 2=retract 238 1 // Short gap motion (between cuts): 0=direct, 1=broken 239 0.2 // Maximum short gap (along cut) as percentage of tool diameter 240 1.0 // Sharp corner tolerance as percentage of chordal deviation 241 1.1 // Maximum short gap (between cuts) as percentage of stepover 242 3 // Tool roll control: 0-between surfaces, 1-all edges, 2-all, if tool center bdy used 403 1 // Z depth control: 0: absolute, 1:incremental 404 0.01 // Incremental top clearance 405 0.01 // Incremental bottom stock 407 0.0 // Absolute top depth 408 -1 // Absolute bottom depth 410 0.1 // Z stepdown 414 1 // Order of z cuts: 0-bottom-to-top, 1-top-to-bottom 415 1 // Cut direction: 0-conventional, 1-climb 421 0 // Graphics cleanup: 0-none, 1-redraw, 2-erase screen 423 0.001 // Minimum contour length 431 1 // Open contour cut direction: 0-zigzag, 1-one way 441 1 // Enable quick zigzag: 0=no, 1=yes 442 0 // Allow tool to plunge outside stock: 0=no, 1=yes 444 1 // Order pockets by 0-depth, 1-level [coons] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 0.1 // Along cut distance 101 0.1 // Across cut distance 102 0 // Blending: 0 = linear, 1 = parabolic, 2 = cubic, 3 = cubic with slope matching 103 0 // Cutting method: 0 = zz, 1 = o.w., 2 = circ., 3 = 5ax zz, 4 = 5ax o.w., 5 = 5ax circ. 104 0 // Cutting direction: 0 = along, 1 = across 105 1 // Graphics: 0 = striped, 1 = solid [loft] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 0.1 // Along cut distance 101 0.1 // Across cut distance 102 3 // Cutting method: 0 = zig zag, 1 = one way, 2 = circular, 3 = 5 ax zz, 4 = 5ax o.w., 6 = 5ax circ. 103 0 // Cutting direction: 0 = along, 1 = across 104 1 // Graphics: 0 = striped, 1 = solid [revolution] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 0.1 // Step size 101 -1.0 // Axis depth 102 1 // Shape: 0 = convex, 1 = concave 103 0 // Retract to: 0 = nothing, 1 = reference plane 104 0.1 // Reference plane height 105 N // Trim surface to: N = nothing, H = height, W = width 106 0.1 // Trimming height 107 0.0 // Trimming width 1 108 0.0 // Trimming width 2 109 1.0 // Trimming width direction 1 110 -1.0 // Trimming width direction 2 [ruled] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 0 // Constant z cutting (0 = no, 1 = yes) 101 0.0 // Initial z 102 -1.0 // Final z 103 -0.25 // Z step 104 0 // Cutting method: 0 = zig zag, 1 = one way, 2 = circular 105 0.05 // Across distance 106 1 // Graphics: 0 = striped, 1 = solid 107 0 // Gouge checking: 0 = off, 1 = parallel, 2 = perpendicular 110 N // Trimming plane 1: X, Y, Z or N (none) 111 0.0 // Trimming plane 1 depth 112 0.0 // Trimming plane 1 point: x 113 0.0 // y 114 0.0 // z 115 0.0 // Trimming plane 1 normal: x 116 0.0 // y 117 0.0 // z 120 N // Trimming plane 2: X, Y, Z or N 121 0.0 // Trimming plane 2 depth 122 0.0 // Trimming plane 2 point: x 123 0.0 // y 124 0.0 // z 125 0.0 // Trimming plane 2 normal: x 126 0.0 // y 127 0.0 // z [2d swept] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 0.15 // Across distance 101 0.7853981634 // RZ: Roll around sharp corners 102 0.7853981634 // XY: Roll around sharp corners [3d swept] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 0.1 // Along distance 101 0.1 // Across distance 102 0 // Rotate (0) / translate (1) the across contour 103 0 // Cutting method: 0 = zz, 1 = o.w., 2 = circ, 3 = 5ax zz, 4 = 5ax o.w., 5 = 5ax circ. 104 0 // Cutting direction: 0 = along, 1 = across 105 1 // Graphics: 0 = striped, 1 = solid [project] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 t // Name of NCI file to project 101 0.0002 // Minimum error from theoretical surface 102 0.001 // Minimum step size 103 100 // Maximum step size 104 0.0 // Cutter radius fort 3d cutter compensation [projsurf] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 t // Name of NCI file to project 101 0 // Add Z depths (0 = no, 1 = yes) 102 1 // Rapid depth 103 0.02 // XY step increment 104 0.0 // Offset distance 105 1 // Graphics (0 = striped, 1 = solid) [projxsec] 1 02500SPH // Tool reference 2 9 // Tool number 3 1 // Tool diameter offset number 4 1 // Tool length offset number 5 0.25 // Tool diameter 6 0.125 // Tool corner radius 7 0 // Compensate to tip (0 = no, 1 = yes) 8 L // Cutter compensation in computer 9 // Cutter compensation in control 10 0.0 // Amount of stock to leave 20 1.0 // Rapid depth 30 40.0 // Feed rate 31 20.0 // Plunge rate 32 5000 // Spindle speed 33 NONE // Material 40 100 // Starting sequence number 41 2 // Sequence number increment 42 0 // Program number 50 0 // Coolant 100 t // Name of NCI file to project 101 0.001 // Minimum step size 102 100 // Maximum step size 103 0.0002 // Minimum error from theoretical surface [edxform] 100 1 // Number of copies 101 0 // Ignore blocks 102 0 // Xform tool plane 103 0 // Delete the original items 104 1 // Reverse cutter compensation direction 110 90.0 // Rotation angle in degrees 111 0.0 // Rotation center: X 112 0.0 // Rotation center: Y 113 0.0 // Rotation center: Z 120 0.0 // Polar angle in degrees 121 1.0 // Polar distance 130 1.0 // Scale factor: X 131 1.0 // Scale factor: Y 132 1.0 // Scale factor: Z 133 0.0 // Scale center: X 134 0.0 // Scale center: Y 135 0.0 // Scale center: Z 140 0.0 // Translation distance: X 141 0.0 // Translation distance: Y 142 0.0 // Translation distance: Z 143 0.0 // Translate between points: From point: X 144 0.0 // Translate between points: From point: Y 145 0.0 // Translate between points: From point: Z 146 0.0 // Translate between points: To point: X 147 0.0 // Translate between points: To point: Y 148 0.0 // Translate between points: To point: Z [ofsctr] 1 1 // Offset direction: 1=Left, 2=Right 2 0.5 // Offset radius 3 1 // Roll around corners (1=none, 2=sharp, 3=all) 4 1 // Use infinite look ahead (1=yes, 0=no) 5 1 // Number of copies 6 2 // Delete old (1=yes, 2=no) [subfig] 1 t // Geometry file name 2 1 // Scale 3 0.0 // Rotation angle (in radians) 4 0 // Mirror X axis (1=yes, 0=no) 5 0 // Mirror Y axis (1=yes, 0=no) 6 0 // Mirror Z axis (1=yes, 0=no) 7 0 // Use main color and level (1=yes, 0=no) [backplot] 1 1 // Tool geometry file name 2 0 // Draw tool reference (1=yes, 0=no) 3 0 // Draw auto tool (1=yes, 0=no) 4 1 // Draw toolpath (1=yes, 0=no) 5 0 // Interpolate along toolpath (otherwise endpoint) 6 0.05 // Interpolation step size 7 1 // Animated tool display (otherwise static) 8 0.0 // Run delay 9 0 // Spin the tool (1=yes, 0=no) 10 0 // Save geometry (1=yes, 0=no) 11 0 // Fit toolpath to screen 12 0 // Stop at NULL tool changes? 13 0 // NULL tool change cleanup (0=none, 1=repaint, 2=clr scrn) 14 0 // Simulate cutter compensation (1=yes, 0=no) [surfshade] 701 892 // Image horizontal size 702 631 // Image vertical size 703 1 // Output to screen (1=yes, 0=no) 704 10 // Always 10 (do not change) 705 20 // Number of pixels per facet 706 50 // Diffuse reflection (0-100) 707 30 // Shiny reflection (0-100) 708 20 // Shinyness of the material (0-200) 709 10000 // Perspective distance 710 0.0 // Background color #1 (R) 711 0.0 // Background color #2 (G) 712 0.0 // Background color #2 (B) 713 4 // Number of palettes 714 100 // Palette #1 - Color (R) 715 100 // Palette #1 - Color (G) 716 100 // Palette #1 - Color (B) 717 0 // Palette #1 - Associate color 718 100 // Palette #2 - Color (R) 719 0.0 // Palette #2 - Color (G) 720 0.0 // Palette #2 - Color (B) 721 12 // Palette #2 - Associate color 722 0.0 // Palette #3 - Color (R) 723 100 // Palette #3 - Color (G) 724 0.0 // Palette #3 - Color (B) 725 10 // Palette #3 - Associate color 726 0.0 // Palette #4 - Color (R) 727 0.0 // Palette #4 - Color (G) 728 100 // Palette #4 - Color (B) 729 1 // Palette #4 - Associate color 730 3 // Number of Lights 731 0.0 // Light #1 - X position 732 0.0 // Light #1 - Y position 733 1000 // Light #1 - Z position 734 100 // Light #1 - Intensity (0-100) 735 1 // Light #1 - State (1=on, 0=off) 736 1000 // Light #2 - X position 737 1000 // Light #2 - Y position 738 1000 // Light #2 - Z position 739 100 // Light #2 - Intensity (0-100) 740 0 // Light #2 - State (1=on, 0=off) 741 -1000 // Light #3 - X position 742 1000 // Light #3 - Y position 743 1000 // Light #3 - Z position 744 100 // Light #3 - Intensity (0-100) 745 0 // Light #3 - State (1=on, 0=off) [curvature] 801 892 // Image horizontal size 802 631 // Image vertical size 803 1 // Output to screen (1=yes, 0=no) 804 0 // Always zero (not used) 805 20 // Number of pixels per facet 806 4 // Curvature type (1=Gauss, 2=Avg, 3=Abs, 4=Min) 807 0.01 // Minimum radius of curvature 808 10 // Maximum radius of curvature 809 0 // Always zero (not used) 810 0.0 // Background color #1 (R) 811 0.0 // Background color #2 (G) 812 0.0 // Background color #2 (B) [batch] 700 0 // Use time limits (1=yes, 0=no) 701 0 // Time limit per surface 702 0 // Time limit per batch task 703 0 // Run post processors (1=yes, 0=no)